ADC225-12V Actuator ESD5111E controller MSP675 Sensor Each One Piece

More details

1.Specification(ESD5111): The speed controller is a closed-loop control of the entire electronic design, it's instantaneous load changes quickly and with precision control in response to engine speed when connected to the match and the implementation of e-speed magnetic sensor signals can be Control of a wide range of engines.  It is designed to be highly reliable, the engine can withstand the surrounding area within the range of electromagnetic interference.  In the design, installation and a simple pre-adjustment, including the transfer rate and adjustable idle for assistance or for multiple special-purpose machine input, as well as to prevent reverse battery voltage, the transient voltage pulse, the actuator short-circuit fault And the loss of power or speed sensor signal of the security protection PERFORMANCE Isochronous Operation/Steady State Stability  ± 0.25% or better   Speed Range/Governor  1K-7.5K Hz continuous  Speed Drift with Temperature  ± 1% Maximun  Idle Adjust CW  Min. 1200Hz. below set speed  Idle Adjust CCW  Min. 4100Hz. below set speed  Droop Range  1-5% regulation  Droop Adj. Max. (K-L Jumpered)  875Hz., ± 75Hz. per 1.0 A change  Droop Adj. Min. (K-L Jumpered)  15Hz., ± 6Hz. per 1.0 A change  Speed Trim Range  ± 200Hz.  Remote Variable Speed Range  500 -7.5Hz. or any part thereof  Terminal Sensitivity  J: 100Hz., ± 15Hz/Volt @ 5.0 K Impedance  L: 735Hz., ± 60Hz/Volt @ 65 K Impedance  N: 148Hz., ± 10Hz/Volt @ 1Meg. Impedance  P: 10V DC Supply @ 20ma Max.  Speed Switch Adjustment Range  1000-10000Hz.  ENVIRONMENTAL  Ambient Operating Temperature Range  -40°c to +85°c   Relative Humidity  up to 95%  Storage Temperature  -55°c ~ 90°c  Shock  20-100HZ 500mm/Sec.  INPUT POWER  Supply  12 or 24V DC Battery Systems(Transient and Reverse Voltage Protected)  Polarity  Negative Ground(Case Isolated)  Power Consumption  50mA continuous plus actuator current  Maximum Actuator Current at 25  10Amps continuous  Speed Sensor Signal  0.5-120 Volts RMS  PHYSICAL  Weight  630g  Package: one 5111E and one manual( wiring diagram ) Note: The performance parameters in the frequency when measuring 4000Hzv 2.Specification(MSP675)  The magnetic speed sensor is mounted in the ring gear case or flywheel bell housing of the engine. The threaded hole for the speed sensor should be perpendicular to the centerline of the crankshaft and  centered over the ring gear teeth. A spot face should be present to provide a flat surface on which to anchor  the locknut.With the engine stopped, screw the speed senor in until it touches a gear tooth, then back it out 3/4  of a turn and secure it with the locknut. Any ferrous gear may be used as long as the frequency and amplitude  of the resulting signal meet the speed control unit specifications The wire leads should be twisted for their entire length from the magnetic speed sensor to the control unit. The leads may need shielding if they are longer than 10 ft. (3m), or if external interference is present. Do not connect either of the speed sensor leads to anything but the speed control unit used. The shield should not be connected at the speed sensor end.  Item            Pickup Length    Thread Length       Lead Length       Thread Size            Drill Size MSP675     3.125"                      2.75"                        7.00"                     5/8-18 UNF-2A       37/64    3.Specification(ADC225-12) Dutys For International Buyers ● Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. ● Please check with your country's customs office to determine what th additional costs will be prior to bidding/buying.● Expedited Shipping(FedEx/DHL/TNT/UPS):TO USA 3-6 Workdays ,TO Other countries 3-8 Workdays● Economy Shipping(Post/Airmail):TO USA 7-12 Workdays ,TO United Kingdom & Australia 20-35 Workdays , TO Other countries 20-50 Workdays ● This is normal condition,but sometimes int'l delivery is highly depended on the courier company and local customs/duties● We only accept Paypal payment.We are not able to ship to PO Boxes or APO/FPO addresses● Please make sure to provide us with correct , precise and detailed shipping Address● And it would be better to leave us correct phone number,so the delivery man can get in touch with you easily when your package arrive .And we wouldn't use your phone number for other purpose.● Order will be shipped out within 1 to 3 business days upon payment received or cleared.● If you don't receive package over 30 business workdays , please notify us.● PayPal payment accepted only.● Items will be shipped to your eBay address. Please make sure it is correct.● Payment must be received 4 days after auction ended.● Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.● If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 30 workdays of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer. ● Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.● When you satisfied with our product and services please leave us positive feedback.● If a problem occurs, contact us immediately with any email request or call us +86 18657106746 directly.If you are not available to make a call, just contact us using the " Ask the seller a question" link on eBay. ● We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 3 business days for us to response. Who we are ?JEENDA MACHINERY CO., LIMITED founded in Wenzhou year 2006,now located in Hangzhou,Zhejiang,China, is a professional supplier of oem and aftermarket generator spare parts and accessories. We provide full range of spare parts and accessories for generating set which includ Leroy somer Alternator parts,Stamford Alternator parts,Marthon Alternator parts,Siemens Alternator parts,Cummins Genset parts,FG wilson Genset parts,Caterpillar genset parts,Perkins Genset parts.The regular products in stock such as AVR(Automatic voltage regulator),GAC and Cummins Speed Governor and Actuator,Deepsea generator controller panel,ComAp generator controller pannel,ATS(Automatic Transfer Swith),Oil pressure Sensors,meters,diode bridge,Battery chargers,Shut down Solenoid,Flame out Solenoid,Turbocharger,Soundproof Material,Water Jacket Heater,Canopy Locks and Hinges,Rain Cap,Lifting Hook,Anti-Vibration Mountings..etc. In one word,JEENDA aims to provide one-stop service for your generator spare parts demand.Quality and Services:The quality of our spare parts is very reliable because we have used original and genuine spart parts used by the original gensets manufacturer.For instance,Company A is using B Company's engine starter,then we buy directly from B Company for engine starter.We use some famous products such as cummins Speed Governor and Actuator which is original OEM parts supply to CCEC and DCEC,DEEPSEA controller panel etc.We also familiar with quality parts-and-accessories suppliers in China.The staff of JEENDA Machinery is honest,reponsible and considerate.They are with good experience in generator industry,too.That's because JEENDA people clearly understand that good professional service,good products serve people one-stop purchasing for genset spare parts for long-term. Engine brands we serve:Those engine brands which we can provide spare parts service includes Cummins(DCEC and CCEC),Perkins,Caterpillar,LOVOL,Yangdong,Weichai,YTO,WEICHAI DEUTZ,VOLVO,JCB,KUBOTA,BOBCAT,CARRIER,THERMO KING,Lister Peter,etc.Future Development ......JEENDA people will stay true to provide one-stop service for our customers.More and more new quality products will be developed and provided to world market.We sincerely look forward to starting up long-term cooperation with all clients and suppliers from  all over the world.Company: JEENDA Machinery Co., LimitedContact: Will Guan Address: No.108, Jian She Er Road, Xiaoshan Economic & Technological Development Zone, Hangzhou 311215 Zhejiang ChinaMOBILE:+86 18657106746 (WhatsApp)          SKYPE:Willamb2012TELL:+86 0571 8272 0939                               EMAIL:Will (at) jeenda (dot) com