New LXC6110 engine auto start generator controller

More details

Product Description: LXC6110 Generator controller  of power plant automation controller for the automation and monitoring system of a single  diesel generator sets, use 32-bit microprocessor technology, achieve generator sets automatic  boot/shutdown, the precision measurement of various parameters, alarm protection and three remote  function. The controller uses a large-screen LCD (240'128LCD) graphics display, all the important  parameters can be displayed in page, save the page. At the same time can be displayed Chinese. English  and other languages, all parameters can be adjusted from the controller panel, can also be a PC through  a USB interface tweaks and RS485 or GPRS remote adjustment and monitoring. Its structure is compact,  simple wiring, high reliability, automation control systems are widely used in all types of generator sets  and fire pumps. Main features: LXC6110:Auto Stare Module, controls genset to start or stop automatically by remote start signal. 1、 With ARM-based 32-bit CPU, highly integrated hardware, new reliability level; 2、240x128 LCD with backlight, multilingual interface(including English, Chinese or other languages)   which can be chosen at the site, making commissioning convenient for factory personnel; 3、All parameters can use the computer via USB, RS232, RS485 interface to connect and adjust, while  the internal FLASH memory within the controller in the system when power is not lost 4、99% of the parameters can be set directly from the front panel for easy on-site commissioning; 5、RS485 communication port enabling remote control,remote measuring,remote communication via ModBus protocol(controller with RS485 port only); 6、Equipped with SMS(Short Message Service)function.when genset is alarming,controller can send short messages vai SMS automatically to max.5 telephone numbers.besides,generator status can be controlled and checked using SMS. With advanced networking capabilities, via GPRS mobile network and Internet connectivity, in any place where the network can be remotely monitor,( Need to install the GPRS module: LX1680); 7、Suitable for 3-phase 4-wire,3-phase 3wire,single phase 2-wire,and 2-phase 3-wire (120/240V)power  and 50/60Hz Systems; 8、Collects and shows 3-phase voltage, current, power parameter and frequency of generator or mains; 9、For Mains, controller has over and under voltage, over and under frequency, loss of phase and phase sequence wrong detection functions; For generator, controller has over and under voltage, over and under frequency, loss of phase, phase sequence wrong, over current functions; 10、3 fixed analog sensors(temperature, oil pressure and liquid level),more kinds of curves of  temperature,oil pressure, fuel level can be used directly and users can define the sensor curves by  themselves; 11、Protection: Automatic start/stop of the genset, ATS(Auto Transfer Switch冲ntrol with perfect fault indication and protection function. When multiple warnings occur, the warning bar will rotate to display them, so that we can analyze the reasons; 12、All output ports are relay-out, And the main output 16A relay outputs and three passive relay output,more user-friendly; 13、Parameter setting: parameters can be modified and stored in internal FLASH memory and cannot be  lost even in case of power outage; most of them can be adjusted using front panel of the controller  and all of them can be modified using PC via USB or RS485 ports. 14、With advanced networking capabilities, via GPRS mobile network and Internet connectivity, in any  place where the network can be remotely monitor; 15、A variety of starting conditions for success (speed sensor, oil pressure, power generation) to select,  to facilitate the needs of special occasions; 16、Wide power supply range (8一35) VDC, can adapt to different environment starting battery voltage  can under the low voltage of starting motor moment continue to work for 3 seconds; 17、Fault history with 200, and can record the fault instant oil pressure， water temperature, voltage,  current and other important parameters; 18、Equipped with real-time clock,regular maintenance functions; 19、Can be used on pumping units and as an indicating instrument (indicate and alarm are enable only,  relay is inhibited): 20、3 set of maintenance functions, can be set for the machine maintenance cycle Maintenance time to action can be set up(only warning or alarm stop); 21、Waterproof security level IP55 due to rubber seal installed between the controller enclosure and panel fascia; 22、Improved LCD wear-resistance and scratch resistance due to hard screen acrylic; 23、Silicon panel and push buttons for better operation in high-temperature environment,and has a good waterproof performance; 24、Modular design,anti-flaming ABS plastic enclosure,plug gable connection terminals adn embedded installation way,compact structure with easy mounting. Special industry application characteristics: 1、 Leasing industry applications: management provides the perfect solution: leased out via PC remote  Management of the unit. you can monitor all operating parameters (oil pressure. water temperature.  voltage, current, power, etc),you can always cnange the configuration to protect the unit is not proper  application, can record 200 detailed fault information, including: time to failure, because， when the  voltage, current, power.oil pressure, water temperature and other key parameters, and ready to  upload to the monitoring machine. Another multi-level password management options to facilitate the  lease management; 2、Fire pump industry applications: Close electrical parameter measurement function, use powerful  Programmable input and output ports and internal programmable logic to achieve automated pump  control system. Instead of the conventional engine controller PLC+simple manner,making the  system more stable and reliable; 3、Air compressor industry applications: Close voltage measurements protection, according to the need  to configure programmable analog input, overload protection，with programmable d心ital inputs,  complete startup control, temperature and pressure control, protection parameter settings. Specifications: Working voltage  DC8.0V to 35.0V (continue to supply) Consumer power ＜3W (stand model: ≤2W ) Alternator voltage input 20V AC - 360 V AC (ph-N) 3 Phase 4wire 3 Phase 4wire 30V AC - 620 V AC (ph-ph) 3 Phase 3wire 3 Phase 3wire 20V AC - 360 V AC (ph-N) 1 Phase 2wire 20V AC - 360 V AC (ph-N) 2 Phase 3wire Frequency 50/60HZ  Speed sensor voltage Vpp  1.0 - 80Vpp  Speed sensor Frequency Max 10000HZ Starting relay output 16Amp DC28V Fuel relay output 16Amp DC28V Programmable relay output 1 7Amp  250VAC passive output Programmable relay output 2 7Amp  250VAC passive output Programmable relay output 3 16Amp  250VAC passive output Programmable relay output 4 16Amp  250VAC passive output Programmable relay output 5 7Amp 250VAC Power supply voltage output (LXC7220) Programmable relay output 6 7Amp 250VAC Power supply voltage output (LXC7220) Current transformer secondary electric 5A Out Size 210mm x 152 mm x 48 mm Tapping Size 186mm x 141mm Working condition Temp. (-25~70) ° C humidity: (20~90)%RH Storage condition Temp.  (-40~+80) ° C Degree of protection IP55:when between the controller and the control screen withwaterproof rubber ring. IP42: when between the controller and the control panel is not equipped with waterproof rubber ring. Insulation strength  Object: the insulation strength between the input / output / power References: IEC6881992 Test method: AC1.5Kv/1min 3mA leakage current  Weight 0.68kg